ALP微型混合活塞夹持装置

ALP Micro Hybrid Plunger Holder

2023-06-21 23:38:06

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

Summary

Atgames Legends Pinball Micro (ALPu) Hybrid Plunger Holder

You have two options:

Digital/Analog Hybrid Plunger: This option allows you to create a hybrid plunger that supports both the ALPu stock tables and OTG tables, including Visual Pinball, Future Pinball, Zen FFX3, and more. With this setup, you'll be able to enjoy a combination of digital and analog functionality. You'll need a PINSCAPE controller for this setup.
http://mjrnet.org/pinscape/BuildGuideV2/BuildGuide.php?sid=pot
Simple Digital Plunger: Alternatively, you can choose to create a simple digital plunger that supports only the ALPu stock tables. This option provides a basic digital functionality. If desired, you can later upgrade to a hybrid plunger by adding analog parts and replacing the plunger head.

Suggest to print with a high infill percentage (60% or more. I did 70% personally). The very strong spring used in the plunger module exerts significant force, resulting in strong impacts on the printed parts. Higher infill percentages will make the parts more solid and better able to withstand these impacts.

Detail parts & setup instruction PDF is included in the download.

Required parts

Common parts
-Hybrid plunger holder (print)
-Plunger module (available at AliExpress, eBay, etc)
https://s.click.aliexpress.com/e/_DB3Bu6v

-19mm dia. magnet sensor switch (Normally Open - NO)
https://s.click.aliexpress.com/e/_Dlo2Bqz
PLS MAKE SURE TO SELECT "NO type", NOT "NC type"

-1 round Neodymium magnet 15mm x 2mm or smaller
-2 4.8 mm male spade connectors

-2 spade male connector https://s.click.aliexpress.com/e/_DmdATXJ
crimping prier https://s.click.aliexpress.com/e/_DDsbSjT

Parts for Digital Plunger
-Plunger digital head (print)

Parts for Hybrid Plunger
-Plunger hybrid head (print)
-1k ohm 128mm (100mm slide length) sliding potentiometer
https://s.click.aliexpress.com/e/_DkOzVS5

-two M3 x ~6mm screws
-appropriate cables and matching connectors to your KL25-based controllers

Caution:
Before opening the ALPu playing field, highly recommend to start by opening the mid back panel. Remove the four black screws and disconnect the three cable connectors attached to the motherboard.
Be cautious when opening the screen lid without disconnecting these cables, as there is a high risk of damaging them and their connectors.

As a hidden option, you can enable the Analog only plunger, supporting OTG tables only. In that way, you will lose a plunger for stock tables. But, you can use the game pad down as a stock table plunger. Kinda awkward to play but it works anyway. :-)

Updates:
6/21/2023 0.98 Initial release