SD卡包含胶带加载/排出和打印机预热G代码，适用于Crazy3Dprint CZ-300及其他型号。

SD Card with filament eject/load and printer preheat gcode for Crazy3Dprint CZ-300 and others

2023-08-24 00:03:05

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

SD卡包含胶带加载/排出和打印机预热G代码，适用于Crazy3Dprint CZ-300及其他型号。

Summary

Copy these files to a spare SD card, and use to make life easier when changing filament or just preparing the printer for a print.

Eject filament will heat the nozzle, and run the extruder motor backwards until filament is out.

Load filament will pull the filament from the extruder towards the nozzle slowly while heating, center and rise the nozzle and wait until hot and then prime the nozzle.

Preheat printer will turn on bed and nozzle and home the axes, so that everything is ready for printing.

Or use the code to adjust your printer setup, what about a Cura setting that eject the filament after each print just in case? Cura printer manage menu has fields to add code to any print.

Check the pdf file for more tips.

For Crazy3Dprint CZ-300, but useful for other printers with minor adjustments.

And to make this a thing, included model for the CZ-300 branded SD card box.

Eject filament gcode

M104 S220 ; set nozzle temp
M105 ; report temp
; give nozzle time to heat to above room temp by heating bed slightly
; sometimes in cold rooms the temp sensor glitches
M140 S30 ; set bed temp
M105 ; report temp
M190 S30 ; wait for bed temp
M109 S220 ; wait for nozzle temp
M82 ; absolute extrusion mode
G92 E0 ; reset extruder position
G1 F200 E3 ; extrude 3mm at 200mm/min feedrate (prime nozzle)
G92 E0 ; reset extruder position
G1 F3000 E-950 ; retract filament fully back and out of extruder
G28 ; home all axes
G1 Z15 F5000 ; lift nozzle 15mm at 5000 mm/min
G1 F4000 X0 Y300.0 ; present bed for cleaning
M84 ; disable motors

Load filament gcode:

M104 S210 ; set nozzle temp
M105 ; report temp
M82 ; absolute extrusion mode
G28 ; home all axes
G1 Z15 F5000 ; lift nozzle 15mm at 5000 mm/min
G0 F5000 X150 Y0 Z50 ; move to nozzle center and bed back
G92 E0 ; reset extruder position
G1 F1000 E830 ; load filament close to extruder
M109 S210 ; wait for nozzle temp
G92 E0 ; reset extruder position
G1 F100 E50 ; extrude 50mm at 200mm/min feedrate (prime nozzle)
M84 ; disable motors

Preheat printer gcode:

M104 S210 ; set nozzle temp
M105 ; report temp
M140 S70 ; set bed temp
M105 ; report temp
G28 ; home all axes
G1 Z15 F5000 ; lift nozzle 15mm at 5000 mm/min
M84 ; disable motors