ORICO 6 in 1 USB C Docking Station - Gridfinity Stackable Base
使用说明
- 所有模型资源均由用户上传分享,内容来源于网络公开资源
- 侵权投诉:通过抖音私信 @jobsfan 联系我们(需附版权证明),24小时内处理
- 模型将通过邮件发送(5分钟内自动发货),感谢理解带宽压力
关于费用
我们是爱好者共建社区,为维持服务器成本,每个模型收取微量费用(仅覆盖基础开支)。我们承诺最低成本运营,感谢您的支持!
扫码手机访问
抖音私信 @jobsfanSummary
This is still a work in progress and I have not yet performed a test print. Sharing in case anyone wants to suggest modifications.
This is a Gridfinity-stackable box to fit around the Orinco 6-in-1 USB-C hub/docking station with ethernet purchased here:
https://www.amazon.com/dp/B0BYS6LGL7?psc=1&ref=ppx_yo2ov_dt_b_product_details
This will eventually be the bottom half of a phone charging stand with ethernet for my desk to fit in with the rest of my ever-growing Gridfinity organization. Rather than fuse the model with the phone stand left it with a Gridfinity baseplate so others can adapt it to their needs. I plan on using glue, screws, or magnets to combine them when I print it for myself. I am still deciding on the top-half to hold the phone, but the idea is the hub will sit under the phone stand and the USB cable in the back will bend up and under the phone stand and use a 90 degree adapter to plug into the phone while it is in the stand.
I threw a few work-in-progress files into the post, but these will likely change drastically before I finalize the post and share it on other sites. The latest version has cut-outs for various purposes.
- Diamond cut-outs on sides and cross cut-outs in the top/bottom are just to reduce filament usage and print time.
- Rectangle cut-outs on sides/back are for ventilation to match the hub's vent holes.
- Rectangle cut-outs on back are for USB, power, and ethernet cables.
- Front cut-out is to slide the hub in, with a small lip to try to hold it in place.
- Hidden hole running from the center-bottom of the top part to the front, well the idea here is to fill it with hot-glue, resin, or something else similar to try to pass the light from the power light on top the hub to the front of the case. No idea if it will work, still to test.
The very thin lines and circles at the corners of the base are to try to allow printing without brim. It's like a mini-brim at only the critical sharp points but with easier cleanup. Just yank or snip them off after printing.
Supports are a must to hold up the top, unless you feel ambitious and want to try printing in a different orientation.
Again, I have not tested this for strength or fit yet. Be warned.
This is a modification of:
Gridfinity Stackable Lids
https://thangs.com/designer/Miss%20Adventure/3d-model/Gridfinity%20Stackable%20Lids-721726
No license listed.
The above in turn is a based on Gridfinity by Zack Freedman, MIT licensed.
https://gridfinity.xyz/
Tags
License
ORICO 6 in 1 USB C Docking Station - Gridfinity Stackable Base
by cheeryhome is licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license.
相关内容
猜你喜欢
联系我们
最新模型
-
盖子和汽油喷嘴2024-05-08
-
TF2守卫Mr.Skin 3D模型2024-05-08
-
瑜伽垫固定挂钩2024-05-08
-
基础火箭模型2024-05-08
-
福克斯尘埃清扫密封压紧装置,36毫米直径2024-05-06
最热下载
-
通用型1/10比例底盘 - DKS基础款2023-03-26
-
ToyREP 3D 打印机2023-03-26
-
六棱锥形微小叶片 - 六叶模型2023-03-26
-
Kumonga的孩子与澳大利亚蜘蛛驯兽队2024-03-17
-
二十面体骰子模型2024-03-29