HWS用参数化偏移钥匙孔钩

Parametric offset keyhole hook for HSW

2024-04-13 06:39:40

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

Summary

This hook allows you to mount objects with those common keyholes on a HSW.
It creates an insert, whith a hook to which you can attach such a hole.
As the distnace between two keyholes is not always a multiple of the distance
between two adjecant Honeycomb fields, it calculates how much this is off and
offsets the hook accordingly.

Configuration

Measure the distance between the centers of the keyholes with a ruler and
put it in total_width.

In most cases this should be enough.

However, if your keyhole doesn't look standard, you can do further adjustements:

Measure the smaller diameter of the keyhole with a caliper and put it in
keyhole_small_diameter.
Measure the larger diameter of the keyhole with a caliper and put it in
keyhole_large_diameter.
keyhole_small_width corresponds to the thickness of the material the
keyhole is in. I'm hanging a small parts magazine to my HSW and the metal
sheet of it's casing is 1.5mm thick.

Here are some illustrations of those parameters:

 |--|    keyhole_small_diameter

  xx   
 x  x  
 x  x  
 x  x  
 x  x  
x    x

x x
x x
x x
xxxx

|------| keyhole_large_diameter

    |----------------|      total_width
┌────────────────────────┐
│                        │
│  ┌─┐              ┌─┐  │
│  │ │              │ │  │
│ │   │            │   │ │
│ └───┘            └───┘ │
│                        │
│                        │

Printing

See .

Mounting

The hooks are only offset on the horizontal axis. Keep that in mind when
mounting them.

Unmounting

As you usually don´t have access to the back of your HSW, you can´t just push
the hook out fro, the back. You can try to carefull pull it out a little on the
pertrusion and then try to get a small flat-head screwdriver under the overhang
of the hex-insert and try to pry it out. This worked for me so far.

Acknowledgements

It also uses the concepts and designs of Honeycomb storage wall.

ThingiVerse

https://www.thingiverse.com/thing:6576683

GitHub

https://github.com/nomike/parametric_offset_keyhole_hook_for_hsw

Instructions

Print the hook as is. Despite the slicer warnining me about floating bridge
anchors and loose extrusions, it printed just fine for me without supports on
my Prusa i3 MK4.

Instructions

Print the hook as is. Despite the slicer warnining me about floating bridge
anchors and loose extrusions, it printed just fine for me without supports on
my Prusa i3 MK4.

Instructions

Print the hook as is. Despite the slicer warnining me about floating bridge
anchors and loose extrusions, it printed just fine for me without supports on
my Prusa i3 MK4.

Instructions

Print the hook as is. Despite the slicer warnining me about floating bridge
anchors and loose extrusions, it printed just fine for me without supports on
my Prusa i3 MK4.