黑客装备炮塔激光安装装置

Hack Pack Turret Laser Mount

2024-04-30 03:03:22

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

Summary

With this 3D printed bracket, you can mount a laser on the front of yourHack Pack* turret.

Disclaimer: Lasers are dangerous. Don't point lasers at yourself or others (including animals). Don't point lasers at airplanes.

The download includes the Fusion 360 source for those who would like to make adjustments.

Additional parts required

6mm diameter laser diode / laser tube (tested with these)
Wires to connect the laser to your Arduino
DuPont connectors and crimping tool if you want to match the stock wiring

Installation

Route your laser wires through the back panel of the turret, alongside the stock wires
Wire up your laser! The positive wire should go to digital pin 8 on the arduino (right next to the stock purple wire). The ground wire can go to any ground pin (next to the stock black wires).Note: The laser I linked has a built in resistor. You may need to wire in a resistor if you use a different laser.
Slide your laser into the laser mounting bracket and route the wires through the cable comb on the back of the bracket. Make sure to leave enough slack for the full range of the pitch servo!
Attach the bracket to the front of your turret. First remove the screws from the short threaded rod. Next slide your bracket in place, lining up the screw holes. Finally, reinstall the screws.
Install laser control code (see the example below)
Test it out!

Sample code

In the PINS AND PARAMETERS section:

int laserPin = 8;
int laserOutput = LOW;

In the setup() function:

pinMode(laserPin, OUTPUT);

A new toggleLaser() function:

void toggleLaser() {
  laserOutput = !laserOutput;
  digitalWrite(laserPin, laserOutput);
}

A new case in the IR receiver switch statement:

case hashtag:
  toggleLaser();
  break;

*This is a referral link that includes a $10 coupon. Just search "Hack Pack" if you don't like referral links.

Print Settings

Rafts:
Doesn't Matter
Supports:
No

联系我们

邮箱: 289047960@qq.com

最热下载

完整的BLTouch/3DTouch指南：针对CR-10/s、Ender 2和Ender 3打印机的自动床级调整（更新版）
2023-03-26
斯坦利杯
2024-01-11
21700毫安电池单元保持架
2024-04-06
NA Miata车灯遮光条折叠机构顶盖
2024-04-15
地牢方块积木，定制升降装置 1x1型定制立管(兼容地下城积木)
2025-07-16

黑客装备炮塔激光安装装置

Hack Pack Turret Laser Mount

使用说明

关于费用

扫码手机访问

Summary

Print Settings

Tags

相关内容

猜你喜欢

联系我们

热门推荐

最热下载

最新模型

黑客装备炮塔激光安装装置

Hack Pack Turret Laser Mount

使用说明

关于费用

扫码手机访问

Summary

Print Settings

Tags

相关内容

猜你喜欢

📩 请输入接收文件的电子邮箱

联系我们

热门推荐

最热下载

最新模型