FIBARO模块住房盒（单开关/双开关）（旧版与新版2.0）或其他模块

FIBARO module housing box for single / double switch (OLD & NEW Version 2) or any other Module

2024-04-24 15:48:29

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

Summary

Here I have created a wall-mounted housing for up to 2 Fibaro modules. It is suitable for both the older design modules with the antenna on the top right side or the newer design modules with the antenna on the right side, such as the FIBARO DOUBLE SWITCH 2. There are two openings for the antenna to pass through.

There is a housing for two Fibaro relay switches for underfloor heating from Homesystem here on Thingiverse (https://www.thingiverse.com/thing:3066450), this gave me the idea of a housing for "normal" single/double switches. I use it to control the lighting and irrigation pumps in the garden house. Since everything is surface-mounted there, I needed a surface-mounted housing with several openings for cable entry. 2 Wago clamps (type 221) can be clamped into the recesses for the power supply (N and L) through the middle opening on the side. There are 2 additional openings for cable entry for each module.
If only 2 single modules or just 1 module are installed, the openings that are not required can be closed with plugs. The lid can be additionally secured with a small screw (countersunk screw 2.5x10 mm), but the lid is already tight and holds even without a screw.
I used the version from robbshop (https://www.thingiverse.com/thing:2741264) to mount the module and merged it with the one from Homesystem in Autodesk Fusion.

The dimensions of the case are 95 x 105 x 28 mm. It can be glued to the wall with mounting adhesive or screwed on. There are 2 versions of the box: Version 1 without holes in the back for glueing to the wall and Version 2 with holes for screwing to the wall.

In this housing everything sits firmly in its place and nothing has to be squeezed into a normal power distribution box from the hardware store. For a water and moisture proof installation, a thin layer of silicone can simply be applied to the lower part of the box's lid holder. To open it, simply cut through the silicone in the slot with a cutter knife. The diameter of the cable entries is 8.6 mm and normal installation cable (TYPE NYM-J 3*1.5mm2) fits exactly through the opening. Here too, the funnel-shaped cable entry on the outside of the box could be sealed with silicone. When uninstalling, the cable can then simply be pulled out of the housing.

I use PLA+ from JAYO in gray for printing. This has a smoother surface, more flexibility and higher strength than regular PLA. The printing is done with supports because of the holes for the cables. These can simply be broken out later.

If you have any questions, requests for changes or just a thank you, write in the comments ;-)

Print Settings

Printer brand:
Creality
Printer:
CR-10
Supports:
Yes
Resolution:
0,2
Infill:
15
Filament brand:
JAYO
Filament color:
grey
Filament material:
PLA+
Notes:
Perfect print temperature is 210 °Grad hotend / 60 ° Grad bed for my Creality CR-10 V3