Makita DC18RC壁挂式电动工具
Makita DC18RC Wall Mount
使用说明
- 所有模型资源均由用户上传分享,内容来源于网络公开资源
- 侵权投诉:通过抖音私信 @jobsfan 联系我们(需附版权证明),24小时内处理
- 模型将通过邮件发送(5分钟内自动发送),感谢理解带宽压力,超过1小时没收到,请联系我们
关于费用
我们是爱好者共建社区,为维持服务器成本,每个模型收取微量费用(仅覆盖基础开支)。我们承诺最低成本运营,感谢您的支持!
扫码手机访问
抖音私信 @jobsfanSummary
I created this model for a friend, as he didn't like the much simpler wall mounts like this as they utilize the holes of the rubber feet, which have to be removed. And the charger is fixed permanently to the wall and can not be quickly removed..
He wanted more like a holster or tray without any modification to the charger itself and the opportunity to just take it off the wall and use it as a mobile charger.
So here it is - just click the charger to the wall and take it off again if needed.
The charger is tilted 15 degrees so that it slightly leans against the wall,and doesn't tend to fall off even if the heavy battery is mounted.It is held by the slightly inward leaning walls plus two "arms" on upper left corner and the right side. As seen on the picture this holds perfectly well, but just in case I also added an optional "safety bracket" which can be inserted in the little pocked on the back side and holds the top of the charger.
To avoid support, the tray is printed separately and the two two triangles need to be glued to it. For correct positioning, the triangles have two little pins that fit into corresponding holes of the tray. Additionally you'll need four 4mm screws to attach it to the wall.
To mount the charger, first insert the bottom and then push it to the wall, slightly bending the arms to the outside until they click in.
Add-on: To guide the cable I added little cable clamps which also allow to attach/remove the cable without unscrewing them. They also need a 4mm screw.
This model is also available on Printables
P.S. The picture also shows four battery mounts found on Thingiverse here and one of my other designs, a holster for a Brother P-Touch H100 handheld printer, which can now also be found on Printables here
Print Settings
- Printer brand:
Creality
- Printer:
CR-10S
- Rafts:No
- Supports:Yes
- Resolution:0.2mm
- Infill:15%-20%
- Filament brand:
Janbex
- Filament color:
yelloow
- Filament material:
PLA
- Notes:
To save material, the tray was printed with only two bottom and 3 top layers (layer height 0.2mm) and only 15% infill. The other parts (mount triangles, safety bracket and cable clamps) were printed with standard Cura settings, i.e. 20% infill. If uncertain, increase infill around the screw holes.
Only minimal support was configured for the tray. I used thin concentric support for the hook of the left arm and the little pocked where the safety bracket can be attached. It might even work completely without support but for this really minimal amount of material I didn't want to challnge it.
The rest was printed without support (mount triangles and cable clips lying on the side) - even for the mount triangles with the overhanging guide pins. Support might be an option for these, but I simply used a pocked knife to slightly scrape the pins.until they fit nicely into the corresponding holes of the tray.
Tags
License
Makita DC18RC Wall Mount
by vivamus3d is licensed under the Creative Commons - Attribution - Non-Commercial license.
相关内容
猜你喜欢
联系我们
热门推荐
-
40×0型风扇安装件(适用于E3DV6型号散热片,中心对齐)2023-05-28
-
宇宙飞船容器2024-01-03
-
Be 200 超级水轰飞机2024-04-09
-
虚假电子烟2024-04-21
-
阿特雷德家族书签——沙丘2024-04-30
最热下载
-
钥匙扣2023-03-26
-
Toyota 22RE发动机扩展套件2023-03-26
-
Ubiquiti UniFi AC Pro 无线接入点支架2024-04-21
最新模型
-
hgx挤出机头火炮响尾蛇 X3 SWX3 HGX lite 2.002025-07-18
-
蝴蝶刀-一体打印(更大刀刃)2024-05-08
-
适用于Qidi Q1 Pro的额外风扇导气管2024-05-06
-
魔幻蘑菇202024-05-06
-
USB-C 12V PWM风扇控制模块外壳2024-05-06