4x10 注册增强模块
4x10 Register Booster
使用说明
- 所有模型资源均由用户上传分享,内容来源于网络公开资源
- 侵权投诉:通过抖音私信 @jobsfan 联系我们(需附版权证明),24小时内处理
- 模型将通过邮件发送(5分钟内自动发货),感谢理解带宽压力
关于费用
我们是爱好者共建社区,为维持服务器成本,每个模型收取微量费用(仅覆盖基础开支)。我们承诺最低成本运营,感谢您的支持!
扫码手机访问
抖音私信 @jobsfanSummary
This is a simple 4x10 register booster I designed to increase airflow for a room that was underserviced by my HVAC system.
There's lots of debate about whether or not boosters are ok for your HVAC system so please use at your own discretion and do your own research. In my situation this was the best short term and quick solution to increase cold air flow into one room in my house.
I used two Delta 80x80x48mm (AFB0824GHE) fans with high static pressure, this is enough to cool the room down a degree or two Celsius below the set temperature at the thermostat.
The assembly is pretty simple, the plate is superglued onto the insert with the side with the two humps/bars facing up, then screw your 80x80 fans onto the plate on the inside of the insert. After this you can wire in your controller and screw your potentiometer onto the grill.
In my case, I screwed the assembled grill/insert/plate into my ceiling. For floor registers I would recommend using M5 screws and nuts to attach the grill to the insert before placing the booster into the register.
Honestly, the fans I used were overkill. They're noisy as all heck, but they do pump air like crazy. I wouldn't recommend using a fan as loud or powerful as these, you could definitely get by with something half as strong and still pump enough air to heat or cool your room comfortably.
Parts I used:
Delta AFB0824GHE 80x8048mm 24v 2 wire fan
Cheap dc voltage controller | https://www.amazon.ca/dp/B07VPNHS5J
24v 2amp power supply
M4/M5 screws and nuts
Superglue
THIS PRINT IS LARGE!
You'll need a bed that can at least print 280mm.
Don't forget to turn off skirt if you're using Cura and the models show up in grey.
Print Settings
- Printer brand:
Creality
- Printer:
Ender-3 Max
- Rafts:No
- Supports:No
- Filament brand:
Filaments.ca
- Filament material:
Econofil PLA
Tags
License
4x10 Register Booster
by thedesmodes is licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license.
相关内容
猜你喜欢
联系我们
热门推荐
-
卡坦岛定居者(完整套装)2023-03-26
-
Grimdark垃圾桶2023-04-09
-
OrangePi Zero LTE 长期支持版硬件外壳2024-03-16
-
单个六边形紧固件夹具2024-04-30
-
artillery hornet 安装支架用于 direct sherpa v2 挤出机2024-05-02
最热下载
-
QC USB充电器外壳(XFW-KC42-4)2024-01-17
-
红米手表4号充电基座2024-03-15
-
原始控制舱2024-03-25
-
空客操纵杆配备控制杆固定装置2024-03-30
-
7英寸HDMI显示器-B外壳2024-04-01
最新模型
-
KSGER T12焊接站背板2024-05-08
-
太阳能板支架2024-05-06
-
漂浮式水耕模型2024-05-06
-
无蝇防虫网安装支架2024-05-06
-
小型乐高宇宙战舰展示底座2024-05-06