十字架式附件 - 德卡顿帐篷MH100(容纳两人)
Cross Clip for Decatlon Tent MH100 (2 People)
使用说明
- 所有模型资源均由用户上传分享,内容来源于网络公开资源
- 侵权投诉:通过抖音私信 @jobsfan 联系我们(需附版权证明),24小时内处理
- 模型将通过邮件发送(5分钟内自动发送),感谢理解带宽压力,超过1小时没收到,请联系我们
关于费用
我们是爱好者共建社区,为维持服务器成本,每个模型收取微量费用(仅覆盖基础开支)。我们承诺最低成本运营,感谢您的支持!
扫码手机访问
抖音私信 @jobsfanSummary
EN
I bought this tent Decathlon MH 100 (2People) a few years ago.
When setting up, the two brackets always unfolded for me. So I always held them together with Velcro, which you use as a substitute for cable ties. But I didn't find this solution very satisfactory. So I created this cross clip with Fusion 360. It is available in 2 versions. Once a little looser and once a little tighter. Then you have to tweak it a bit. The clip held up very well and is easier to attach than fiddling with the Velcro. Especially if you come to the campsite late in the evening and it is already getting dark.
Note: The clip can only be installed in a certain direction. Lower arch from front left to back right. Upper arch from front right to back left.
Due to the roundness of the arcs, it is necessary to print the part upside down using supports. Then the channel into which the carbon rods go must be sanded clean so that there are no scratches. I always leave the part in the pocket of the tent. This clip may also fit the three-man version of this tent.
Happy camping!
DE
Ich habe mir vor einigen Jahren dieses Zelt Decathlon MH 100 (2People) gekauft. Beim Aufbauen sind mir immer die beiden Bügel auseinandergeklappt. Also habe ich sie immer mit einem Klettband ,welches man als Ersatz für Kabelbinder nimmt, zusammengehalten. Ich fand diese Lösung aber nicht so befriedigend. Also habe ich mir mit Fusion 360 diesen Cross Clip erschaffen. Es gibt ihn in 2 Versionen. Einmal etwas lockerer und einmal etwas straffer. Da muss man dann etwas nachfeilen. Der Clip hat sehr gut gehalten und ist simpler anzubringen als mit dem Klettband rumzuhantieren. Besonders wenn man spät abends auf den Campingplatz kommt und es schon dunkel wird.
Beachtet: Der Clip lässt sich nur in einer bestimmten Richtung einbauen. Unterer Bogen von vorn links nach hinten rechts. Oberer Bogen von vorn rechts nach hinten links.
Aufgrund der Rundung der Bögen ist es erforderlich, das Teil kopfüber zu drucken und dabei Supports anzuwenden. Danach ist die Rinne in welche die Karbonstäbe hineinkommen sauber auszuschleifen, damit an den Stäben keine Kratzer entstehen. Das Teil lasse ich dann immer in der Tasche des Zeltes. Eventuell passt dieser Clip auch bei der Dreiermann Version dieses Zeltes.
Viel Spaß beim Zelten!
Print Settings
- Printer brand:
Creality
- Printer:
Ender-3 v2
- Supports:Yes
- Resolution:0.16
- Infill:98% Lines (clip), 25% Gyroid (crossection)
- Filament brand:
iFilament (Germany)
- Filament material:
PETG
- Notes:
When you need an other angel by the cross send me a message and a photo from above of your tent carbon arks.
Tags
License
Cross Clip for Decathlon Tent MH100 (2 People)
by 3DeeForm is licensed under the Creative Commons - Attribution license.
相关内容
猜你喜欢
联系我们
热门推荐
-
复古风格闹钟架2023-03-26
-
圣诞彗星3D模型2024-01-15
-
Wifi Trax-WFD 30 外壳2024-01-16
-
微USB转换为标准USB 3D模型2024-02-04
-
新日插头2024-05-04
最热下载
-
21700毫安电池单元保持架2024-04-06
-
浴室排水器2024-04-07
-
地牢方块积木,定制升降装置 1x1型定制立管(兼容地下城积木)2025-07-16
-
P90 AEG型号空气枪到Odin Airsoft速率加载器适配器2024-05-01
-
史诗级生存刀具2024-05-03
最新模型
-
嵌入式保险杠防护板2024-05-08
-
第二屏幕2024-05-08
-
3D模型标题:吊坠 2.75厘米2024-05-08
-
猎人轮椅(血源粉丝艺术)2024-05-06
-
Mk2冷液泄漏散热器夹具2024-05-06