德威特 DCV581H 真空消气器
DeWalt DCV581H Vacuum Defuser
使用说明
- 所有模型资源均由用户上传分享,内容来源于网络公开资源
- 侵权投诉:通过抖音私信 @jobsfan 联系我们(需附版权证明),24小时内处理
- 模型将通过邮件发送(5分钟内自动发货),感谢理解带宽压力
关于费用
我们是爱好者共建社区,为维持服务器成本,每个模型收取微量费用(仅覆盖基础开支)。我们承诺最低成本运营,感谢您的支持!
扫码手机访问
抖音私信 @jobsfanSummary
Defuser to redirect exhaust air from 20v DeWalt Vacuum DCV581H. 2 Pieces printed and then pressed together. A little sanding on the inside edge of part A on the hexagonal side can help fit pieces together. If it is too hard to fit, print Part B 1-1.5% smaller. I didn't need to as I just sanded the inside edge of Part A just before the internal ring a little then set Part B on ground with tube side up; slid part A with Barbed side up and hit with a rubber mallet to press together.
Printed with supports, part B with words up. Takes a little work to clear out the supports from inside (long nose pliers, twist & pull with determination) can clear out the supports. Part A I printed with the hexagonal side down and supported the tabs from the base up just to keep them square. Tabs might need to be sanded a bit, but mine fit without any sanding. Make sure tabs are horizontal when inserting then twist hex base 1/8 turn to the right to lock in.
Printed in PLA with 30% triangle infill for some strength using an Ender 5+ with Sonic Pad and a 0.40mm nozzle.
Print Settings
- Printer brand:
Creality
- Printer:
Ender-5 Plus
- Rafts:No
- Supports:Yes
- Resolution:.20
- Infill:30%
- Filament brand:
Elegoo
- Filament color:
Grey
- Filament material:
PLA
- Notes:
2 Pieces printed and then pressed together. A little sanding on the inside edge of part A on the hexagonal side can help fit pieces together. If it is too hard to fit, print Part B 1-1.5% smaller. I didn't need to as I just sanded the inside edge of Part A just before the internal ring a little then set Part B on ground with tube side up; slid part A with Barbed side up and hit with a rubber mallet to press together.
Printed with supports, part B with words up. Takes a little work to clear out the supports from inside (long nose pliers, twist & pull with determination) can clear out the supports. Part A I printed with the hexagonal side down and supported the tabs from the base up just to keep them square. Tabs might need to be sanded a bit, but mine fit without any sanding. Make sure tabs are horizontal when inserting then twist hex base 1/8 turn to the right to lock in.
相关内容
猜你喜欢
联系我们
热门推荐
-
Morton安全玻璃破碎系统2024-02-04
-
双面哥布林:你的新朋友2024-04-19
-
单个六边形紧固件夹具2024-04-30
-
英国K级潜水艇3D模型2024-04-30
最热下载
-
模块化抽屉 2.02023-03-26
-
Articulated Snake2024-03-30
-
空客操纵杆配备控制杆固定装置2024-03-30
-
7英寸HDMI显示器-B外壳2024-04-01
-
Ikea 米兹顿 插嵌2024-04-20