床摇晃问题终结：EnderXY解决方案

EnderXY - Bed Wobble Be Gone

2024-01-16 03:46:09

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

床摇晃问题终结：EnderXY解决方案

床摇晃问题终结：EnderXY解决方案

Summary

Join the EnderXY community on Reddit:
https://www.reddit.com/r/EnderXY/

I've made this as I've received a few messages on here asking if there was a way to fix the bed wobble without using triple-z. This is untested as I use triple-z, but it should work and fix the issue completely.

Remember to print 2040 linear rail guides before dissasembly to make the installation easier, I've included some to print (atleast 2).

You will lose 10mm on X as the motor had to be shifted, effectively moving the bed back 10mm so that the linear rail and lead screw are parallel, though this also depends on the thickness of the toolhead you are using.

Note: If you are using the printed bracket and location designed by belt3dprinterkit then you will have to flip the bracket (check pictures).

Motor mount (Pic 7):

4x M3x15mm (Socket or Pan head)
4x M3x10mm (Socket or Pan head)
4x M3x13mm (Socket or Pan head)
4x M3 spring nuts (Re-use stock)

Arm (Pic 4, 5, 6):

8x M3x8mm (Socket or Pan head)
8x M5x8mm (Re-use stock)
4x M3x13 or 15mm (Socket or Pan head)

Z-endstop mount (Pic 8):

1x M5x8mm (Pan head)
1x M5 spring nut (Re-use stock)
2x M3x6mm
1x M3x18mm (Adjustment)

Dissassembly:

Remove heated bed from bed carriage.
Remove stock arms (P4L/P4R in the manual) and 1020 extrusions.
Remove 1020 extrusions from stock arms (P4L/P4R in the manual).
Remove linear rails and carriage
Remove motor.
Remove Z nut from lead screw.
Remove lead screw from coupler.
Remove coupler from motor.

As screws cross paths there is a very specific order that has to be followed for installation.

Linear rail and carriage installation:

Use 2040 linear rail guides to align the rails.
The rail should touch the lower brackets (P3L/P3R in the manual).

Motor installation:
Connect mount to 2040.
Connect motor to mount.
Add Z rod coupler.

Arm installation:

Connect arm to MGN12H (top bolts ONLY).
Connect Z nut to arm.
Connect arm to MGN12H (bottom bolts ONLY).
Connect 1020 extrusions to arm.
Connect lead screw.

Z-endstop mount:

Follow the picture.

Remember this is untested until I get confirmation but I'm pretty sure there won't be any issues.

If you'd like to support my work you can here https://ko-fi.com/supavitax

Original model at thangs.com: https://social.thangs.com/m/992921

Tags

aditiva3d bed belt3dprinterkit corexy Ender Ender3 EnderXY wobble

License

CC BY-NC

EnderXY - Bed Wobble Be Gone
by Supavitax is licensed under the Creative Commons - Attribution - Non-Commercial license.

床摇晃问题终结：EnderXY解决方案

朋友，你觉得上面这个模型，属于下面的哪个分类？

上面没有我要的选项

必须全中文，且长度不超过15

相关内容

猜你喜欢

联系我们

邮箱: 289047960@qq.com

热门推荐

最热下载

BlueSCSI v2 SPARCstation驱动器支架及密封环
2024-04-14
JeNo 3" 笼罩 DJI O3 + 支架 + 电池保护 + 40° 防撞器
2024-04-19
厨房水槽滤网过滤器
2025-06-05
Myuto Flick 19X - 可工作的玩具枪（橡皮筋弹弓状枪）
2025-08-17
Flick 19E（增强型） - 可使用的玩具枪 - 类似弹弓的橡皮筋枪
2025-08-21

最新模型