Flashforge Adventurer 3 HEPA 空气过滤器

Flashforge Adventurer 3 HEPA Air Filter

2024-05-02 15:17:55

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

Summary

I wanted to add a charcoal+HEPA air filter to my Flashforge Adventurer 3, but the Flashforge Adventurer 3 filter on Amazon seemed expensive at about £19.00 each. So I wanted one that I could print out, but could not find any. The 3D printable models that were available used filters that I could not find in the UK.

So I decided to use the filter for the Adventurer 4, which can be bought from Flashforge for delivery in the UK:
https://www.flashforgeshop.com/product/air-filter-for-flashforge-adventurer-4-series?cID=63. The cost of these, incluidng postage, is about £45 for 5, so about £9.00 each.

I decided to re-mix the 3D printable model from Kakeru Nekobeya :https://www.thingiverse.com/thing:4763031/comments.

This had a cut-out to allow for the fan, a cut-out for the ledge at the back (where the top meets the back) and an air space above the filter to allow air to be drawn across the whole filter. Unfortunately, the filter it used was 11.5cm square and did not seem available in the UK,

So, I have reduced the size to take the 8.00 cm square Adventurer 4 filters and added four, 6x2 mm Neodymium magnets to secure the filter case to the top of the printer cabinet. The actual filter then pushes in and simply holds itself, temporarily, in place. However, with use the filter seems to shrink and will drop out, jamming the printing plate. So I have created a lid that will hold it in place too.

The magnets were glued in with Gorilla Epoxy glue and left to set overnight before use.

I was printing PLA on a Anycubic Kobra 2 Max and had some issues with added support being difficult to get out of the holes for the magnets, but I found the following settings in Cura helped:

Support pattern: Zig Zag
Support Density 5%
Support Line distance 8
initial Layer Support Line distance 8
Support Z distance 1 mm
Support top distance 1 mmI wanted to add a charcoal+HEPA air filter to my Flashforge Adventurer 3, but the Flashforge Adventurer 3 filter on
Support x/y distance 1.5 mm
Support Z distance 1.0

Since I made this, I have also found the Muliap SY901 Air Purifier Replacement Filters , which are 3.5” (9.89cm) square and cost £12.29.

https://www.amazon.co.uk/Muliap-SY901-Purifier-Replacement-Filter/dp/B0CMPYX166/ref=sr_1_3?crid=2LIDRZ754BYQ9&dib=eyJ2IjoiMSJ9.qzzXlkyLbWSrCpJFgDpRiAe03tpROPYNGATyU97iKJeUiyMzTOXfMscwotUYlHuWyNJf3V0nbDscvfM9wiVf1sESD7Uop2mf7joG_Cd4lcTGg5BJr6oop2knsSf3VBbtCddldfvl7Q-U-gGhxkyxrgJjJXeY0fRLKJYwR9eYOqQ-870IdYKvWPKhNnSTSnyvfVrDw1BF8mvbhoNZfDxxCcUQZgFNgjgAR33z_cXNVHs.1ECl1BR3DBomOpJqUXD7KaLqItgxnHivquiEs8P6r8k&dib_tag=se&keywords=muliap%2Bair%2Bpurifiers%2Bfilters&qid=1713284570&sprefix=Muliap%2BAir%2BPurifiers%2B%2Caps%2C87&sr=8-3&th=1

If anyone wanted to, it should be possible to remix the model to take these too. Although it is more expensive, you do not have to buy 5 at a time.