可调节亮度双LED头板灯
Dimmable Dual LED Headboard Light
使用说明
- 所有模型资源均由用户上传分享,内容来源于网络公开资源
- 侵权投诉:通过抖音私信 @jobsfan 联系我们(需附版权证明),24小时内处理
- 模型将通过邮件发送(5分钟内自动发送),感谢理解带宽压力,超过1小时没收到,请联系我们
关于费用
我们是爱好者共建社区,为维持服务器成本,每个模型收取微量费用(仅覆盖基础开支)。我们承诺最低成本运营,感谢您的支持!
扫码手机访问
抖音私信 @jobsfanSummary
Simple little enclosure and dual strip light bar for 8mm strip LEDs.
The box has amini PWM motor controllerandSPDT switchto control dimming and select which LED strip is enabled. Power is provided via a5521 jack. No glues or screws are needed for assembly, only some VHB tape to mount the bar in it's final position. Because of the shape of the bar, you don't need adhesive strips for this to work. They slot in and are retained, so they can't fall off or sag. I printed in PLA+ using two walls and 10% gyroid infill; the rods at 0.28mm height and the box at 0.2mm height.
Each bar is 8" (203mm) long, so figure out how many you need. In my use I made a 2' (0.6m) long bar that was made from the box, lid, two extensions, and a female end.
There is 0 tolerance in these parts, which for my printer is fine. I printed the bars upright, only using supports in the female sockets of the extensions, and cleaning the brim flashing off with a hobby knife. The fit is exact so no adhesive or screws are required.
Print the box face down with a little support for the male extension out one end. The lid should print outside face down. There are retention tabs built in that will allow the two to snap together when assembled without screws or adhesives.
I would suggest assembling the rod to measure out your strips and cutting them to length, then soldering ~3" leads to the strips. From there pass the leads through the diamond holes on the box and attach the rod to the box. With the lead wires now available, solder together the switch and screw in the wires to the dimmer. Bolt down the switch and dimmer and you're done!
I put a few chunks of VHB tape on the top of the assembly and stuck it to one of my kid's headboards, so now he has a good reading light as well as a fun blacklight for all his glow-in-the-dark toys and prints. The whole thing runs off an old salvaged Blackberry charger that I stuck a 5.5x2.1 90° plug on.
Print Settings
- Printer brand:
Bambulabs
- Printer:
Bambu X1C
- Rafts:No
- Supports:Yes
- Resolution:0.20 and 0.28
- Infill:10% Gyroid
- Filament brand:
eSun
- Filament color:
Black
- Filament material:
PLA+
Tags
License
Dimmable Dual LED Headboard Light
byRevHazlettis licensed under theCreative Commons - Attribution - Non-Commercial - Share Alikelicense.
相关内容
猜你喜欢
联系我们
热门推荐
-
特斯拉 Mini 3 Pro 无线遥控自行车支架2023-03-26
-
Voxelab Aquila可连接床手柄2023-03-26
-
Geeetech A10 DD Orbiter 2.4 E3dV62023-04-21
-
亚当·默菲 ODM 定制硬件模型 [ AOT 系列 ]2024-01-13
-
威伯克格拉迪安NXT S形扩展模块2024-03-23
最热下载
-
QC USB充电器外壳(XFW-KC42-4)2024-01-17
-
Articulated Snake2024-03-30
-
浴室排水器2024-04-07
-
Dyson V6系列3D模型适配器站2024-04-15
最新模型
-
MK8挤出机散热风扇管道支撑结构2024-05-08
-
为我的教学2024-05-08
-
自行车电池计量架2024-05-08
-
伊比休鸽子鸨夫2024-05-08
-
适用于MK2 Scirocco的三件式格栅夹具套装2024-05-06