天文望远镜平面盖

Telescope Cover with Flatbox

2023-08-07 01:10:42

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

Summary

The telescope cover is for use with a 8" Newton or RASA telescope.
Covers in other sizes can be adapted.

Size up to 10" incl. lightbox was tested, yet 10" version is already very heavy due to the acrylic plates of the lightbox.

Printing the cover requires a 3D-printer with at least 300x300 of bedspace, otherwise the design has to be adapted.

Control of the cover and the lightbox is done via ASCOM utilizing the software and drivers by jlecomte:
github.com/jlecomte/ascom-flat-panel
github.com/jlecomte/ascom-telescope-cover

Perform the soldering according to his instructions as well.

To get the 270° motion I needed to use a 300° servo. I tried a 270° servo, but it would not achieve a full rotation. Adjustments to the Arduino code for opening an closing may be required.

Required hardware:
2x Seeduino XIAO
1x Servo 300° (https://tinyurl.com/35fev5ph)
11x M3 threaded inserts: (https://tinyurl.com/2fjhxz5j)
2x USB-C Cable e.g. (https://tinyurl.com/56yz3bum)
2x Buck-converter 360mini (https://tinyurl.com/42wt9bsd)
or for larger OTA:
1x 360 mini DC to DC converter for the light (https://tinyurl.com/42wt9bsd)
1x Lm2596S DC-DC converter for the servo (https://tinyurl.com/42vc923t)
1x Servoarmdisc 25T (https://tinyurl.com/45annv7t)
1x Rollerbearing MR105-2RS
1x Threaded insert M5 (to attach telescope cover)
1x IRF520N Mosfet for lightbox
1K OHM resistor
2x DC Power Jack or Cable for 12V Power
1x M5 bolt 15mm to attach the cover
1x M5 bolt 25mm as achsle

The Lightbox acrylic plates were taken out of a 24W Led lamp: (https://tinyurl.com/4735u8zf)
For illumination a 12V Led Strip was used: (https://tinyurl.com/2ssxxdyf)
It is recommended to adjust the Voltage down to approx. 9V-10V to reduce brightness.
Be aware to limit the voltage for the Servo according to its specs.
Further adjustments to the brightness can be done in software as well.

Required software:
As per github by jlecomte. It is recommended to read his instructions on how to wire the microcontrollers and install the ASCOM drivers.

Use one microcontroller for the cover and the other one for controlling the light.

Print Settings

Printer brand:
VoronDesign
Printer:
Voron2 350
Rafts:
No
Supports:
No
Resolution:
0.2
Infill:
23
Filament brand:
ESUN
Filament color:
black
Filament material:
PLA or ABS

Post-Printing

Flange needs to be glued to the cover.

It put some additional 3D-models for different OTA sizes, a 15mm longer version of the motorbox and a cover for 10" Newton in as well.
For the 10" cover a 36W LED lamp has to be scavenged and the acrylic plates have to be cut to size without damaging them to fit on a 350x350 printer.