PS5访问控制器第二个手柄

PS5 Access Controller Second Stick

2024-03-15 18:57:20

使用说明

所有模型资源均由用户上传分享，内容来源于网络公开资源
侵权投诉：通过抖音私信 @jobsfan 联系我们（需附版权证明），24小时内处理
模型将通过邮件发送（5分钟内自动发送），感谢理解带宽压力，超过1小时没收到，请联系我们

关于费用

我们是爱好者共建社区，为维持服务器成本，每个模型收取微量费用（仅覆盖基础开支）。我们承诺最低成本运营，感谢您的支持！

扫码手机访问

抖音私信 @jobsfan

Summary

Ongoing development - feedback welcome!

Part of a collection of button caps and external switches for the Playstation Access controller:
https://www.thingiverse.com/harakan/collections/41421121/things

Extra analog thumbstick/joystick for the Playstation Access controller.

For each stick, you will need:

One dual-axis joystick module, 26mm x 34mm compatible with KY-023 (e.g. https://www.amazon.com/DIYables-Joystick-Arduino-ESP8266-Raspberry/dp/B0BPGRN48J)
One 3.5mm 4-pole connector (e.g. https://www.amazon.com/Fancasee-Replacement-Connector-Headphone-Microphone/dp/B07Y8JNGW1)
(Optional) One 3.5mm 2-pole connector (e.g. https://www.amazon.com/Fancasee-Replacement-Repair-Solder-Connector/dp/B07Y8JHK9P) OR a second 3.5 4-pole connector
One 1 x 5-pin 2.54mm Dupont female connector (e.g. https://www.amazon.com/WEKESIGO-1550PCS-Connector-Headers-Balancer/dp/B09Z2SWNDR)
4-conductor cable (e.g. https://www.amazon.com/Conductor-Electrical-Stranded-Extension-Automotive/dp/B0C2HB7NL1)

Any thumbsticks compatible with Arduino/PS2/PS3/PS4 can be used if one is not included with the joystick module.

A wide variety of 3D-printable accessible joysticks, including sticks, balls, goal-post, and chin-operated versions can be used with the HandiAdapter here:

https://www.thingiverse.com/thing:6526366

Assembly instructions:

NOTE: For the push-switch to operate correctly, the joystick is wired with the opposite polarity to the Arduino (VCC/GND swapped), and the cable connector at the top.

Wire the 3.5mm 4-pole connector to the Dupont connector as follows (for details see https://www.playstation.com/en-gb/support/hardware/access-specifications/):
- Sleeve (Vdd) to pin 1 (marked as "GND" on the joystick)
- Ring 2 (Gnd) to pin 2 (marked as "+5V" on the joystick)
- Ring 1 (X-Axis) to pin 3 (marked as "VRX" on the joystick)
- Tip (Y-Axis) to pin 4 (marked as "VRY" on the joystick)
For the push-switch, wire the second 3.5mm connector tip to pin 5 of the Dupont connector. Only a single wire is needed - do NOT connect the sleeve/R1/R2 pins to the joystick. If using a 4-pole connector instead of a 2-pole connector, connect the sleeve/R1/R2 pins together but NOT to the joystick.
Test the joystick by connecting it to the Access controller and configuring a profile to set the external port as Left or Right stick. If using the push-switch, set the second external port to Triangle. Start the "Astro Playroom" game on the PS5 and select "Controller Demo". The image of the controller should show the joystick move in the correct directions and the triangle button being pressed. Check that the full range of motion is correct and that the joystick centers correctly.
Clip the joystick module into the base, angling it so that the pins align on one side before pressing down on the other side. Feed the cable through the cable guide, and fit the thumbstick/joystick, before finally clipping on the top. Check that the joystick has the full range of motion. Use the top with the larger joystick hole if necessary.