计数光盒
Talley Light box
使用说明
- 所有模型资源均由用户上传分享,内容来源于网络公开资源
- 侵权投诉:通过抖音私信 @jobsfan 联系我们(需附版权证明),24小时内处理
- 模型将通过邮件发送(5分钟内自动发货),感谢理解带宽压力
关于费用
我们是爱好者共建社区,为维持服务器成本,每个模型收取微量费用(仅覆盖基础开支)。我们承诺最低成本运营,感谢您的支持!
扫码手机访问
抖音私信 @jobsfanSummary
This is a design for a DIY Tally Light box for visual indication of multi-camera queuing to talent.
This design is meant to enclose the 7 RGB LEDs (WS2812B-3535) shield onto a mini WiFi board based ESP32-S2FN4R2 for Wi-Fi IOT.
Assembled, these two-boards fit into the Tally light container that accommodates access to the USB C power/programming interface, and the ESP32-S2FN4R2 reset buttons.
Programming for one or more Tally light boxes can be found at the following link.
https://github.com/pastorhudson/MicroTally/releases/latest
Potential circuit sources https://www.amazon.com/dp/B0B9ZZYFZ4?ref=ppx_pop_mob_ap_share&th=1
and https://www.tinytronics.nl/en/wemos-lolin-7x-ws2812b-led-shield-for-d1-mini
A USB C power plug will also be required.
Print Settings
- Printer brand:
LulzBot
- Printer:
Mini 2
- Rafts:No
- Supports:Yes
- Resolution:standard
- Infill:90
- Filament brand:
MH | BUILD
- Filament color:
clear
- Filament material:
PETG
- Notes:
The container can be printed without supports. However, the Top will need supports. A Brim is advised for both prints.
A single 3mm x 4mm screw is used to secure the top to the container. An appropriate hole should be drilled in the correction position using the guide hole in the top piece.
A third print option is available for printing with a non-translucent filament. The H version container has an open front that can be sealed with a piece of white paper (preferably from the inside as an insert) or left open. A non-translucent top will still allow light to be reflected to a camera operator through a rear facing hole. The amount of light moving to the rear can be increased by inserting an opaque surface in front of the LEDs such as a piece of whit paper.
How I Designed This
Temperature differential of a sealed unit is tested to be < +3 °C between inside and outside with an exterior ambient temperature of 22 °C after 1 hour of continuous operation.
相关内容
猜你喜欢
联系我们
最新模型
-
盖子和汽油喷嘴2024-05-08
-
弗罗贝起重机2024-05-08
-
德沃尔特快速连接2024-05-08
-
砂布圆盘转孔2转换器2024-05-08
-
FAN SHROUD FOR PWNCNC VFD2024-05-06
最热下载
-
ToyREP 3D 打印机2023-03-26
-
六棱锥形微小叶片 - 六叶模型2023-03-26
-
Dado - 立方体模型2024-03-24
-
泰坦电视核心升级2024-05-02
-
旅行游戏盒2024-05-08